HTf213

Technical Details:
The kit includes an Ht213 spinning rod holder and an FFr222 mounting system. The design of the holder consists of a body, a retainer, an end limiter, a hole for attaching a safety leash carabiner, the tilt 27.7° splines joint, completed with 7.5° splines Dp230 adapter washers and fasteners (an M6*50 DIN 931 screw and an M6 DIN 934 nut with a hex knob) and a male adapter shaped as a 12 pointed star for installation in the mount. The Fs219 mount is attached to the Fr222 mounting pad with four M6*20 DIN 912 screws and M6 DIN 985 self-locking nuts. The package includes collars with M6*40 DIN 931 screws and hex knob nuts, a set of caps for protecting the collars against rusting, a set of caps for installing on the FeelFree tracks. The holder, the mount, the pad and caps are made of fiberglass-reinforced polyamide. Fasteners — of A2 (AISI 304) stainless steel (except for three M6 DIN 934 brass nuts).

Product description:
This kit (Ht213 + FFr222) has been designed for mounting a spinning rod holder on kayaks with upward-directed T-Track. A special feature of this kit is that it includes everything you need for installing on the Feel Free kayak, which has a non-standard shape track, including a set of caps against rusting.
The large mounting area and two T-bolts make the kit stronger than single-bolt T-Track adapters and allow the kit to be used for higher loads.
The holder is suitable for spinning rods with different types of reels and a handle diameter of up to 38 mm. In the front part of the holder there is a cut for fixing spinning rods with a fixed-spool reel.
The handle of the spinning is securely fixed with a retainer in the holder, which protects the tackle from loosing and falling into the water during trolling, when biting large fish and during transportation. It also allows you to quickly get out the rod if necessary.
There is an end stopper at the rear of the holder, which serves as a limiter and prevents axial rotation of rods with the end cruciform slot. It also can be taken off when fixing long-handled spinning rods.
At the bottom of the holder there is a hole for attaching a safety leash carabiner, which allows you to maximally protect the tackle from loss.
The holder and the adapter, which are fixed in the mount, are connected by the tilt 27.7° spline joint. Thanks to the washers with smaller splines provided into the joint assembly, the holder with the fixed spinning rod can be tilted in 7.5°, providing flexible adjustments. The selected tilt angle is fixed with the hex knob nut.
The plastic body of the holder protects the spinning rod from damage (compared to metal holders).
Materials: fiberglass reinforced polyamide, PVC, A2 (AISI 304) stainless steel, brass.
In the package: an Ht213 spinning rod holder, an FFr222 mounting system, a set of caps.
Tips on using & installation:
You can separate the splines of the tilt joint in order to supply it with BORIKA FASTen® extenders with 27.7 side splines and lengths from 10 to 30 cm. Please note that this model should be used with caution in combination with extenders, because the structures on which the mounting system with a fixed holder is attached (in this case, a T-Track) are not always designed for the increased dynamic loads unavoidable during trolling.
The mounting pad is installed on the track using two metal plates (clamps), complete with sets of plastic caps for protection against rusting and for installation on FeelFree tracks. Using two hex plastic knobs you can move the system along the track and fix it in the selected place.
After the end of fishing, the spinning rod adapter can be easily removed from the mount and the mounting system can be used to fix other BORIKA FASTen® accessories.
To prolong the service life of the product, after using it in sea water, it is recommended to rinse it with plenty of fresh water.